| GevPhysicalLinkConfiguration |
Controls the principal physical link configuration to use on next restart/power-up of the device. |
| GevCurrentPhysicalLinkConfiguration |
Indicates the current physical link configuration of the device. |
| GevSupportedOptionSelector |
Selects the GEV option to interrogate for existing support. |
| GevSupportedOption |
Returns if the selected GEV option is supported. |
| GevInterfaceSelector |
Selects which logical link to control. |
| GevMACAddress |
MAC address of the logical link. |
| GevPAUSEFrameReception |
Controls whether incoming PAUSE Frames are handled on the given logical link. |
| GevPAUSEFrameTransmission |
Controls whether PAUSE Frames can be generated on the given logical link. |
| GevCurrentIPConfigurationLLA |
Controls whether the Link Local Address IP configuration scheme is activated on the given logical link. |
| GevCurrentIPConfigurationDHCP |
Controls whether the DHCP IP configuration scheme is activated on the given logical link. |
| GevCurrentIPConfigurationPersistentIP |
Controls whether the Persistent IP configuration scheme is activated on the given logical link. |
| GevCurrentIPAddress |
Reports the IP address for the given logical link. |
| GevCurrentSubnetMask |
Reports the subnet mask of the given logical link. |
| GevCurrentDefaultGateway |
Reports the default gateway IP address to be used on the given logical link. |
| GevIPConfigurationStatus |
Reports the current IP configuration status. |
| GevPersistentIPAddress |
Controls the Persistent IP address for this logical link. |
| GevPersistentSubnetMask |
Controls the persistent subnet mask associated with the Persistent IP address on this logical link. |
| GevPersistentDefaultGateway |
Controls the persistent default gateway for this logical link. |
| GevPersistentARPConflictDetectionEnable |
Enables ARP Conflict Detection for persistent IP addresses. Warning: Disabling may result in the inability to communicate with the device! |
| GevDiscoveryAckDelay |
Indicates the maximum randomized delay the device will wait to acknowledge a discovery command. |
| GevGVCPExtendedStatusCodesSelector |
Selects the GigE Vision version to control extended status codes for. |
| GevGVCPExtendedStatusCodes |
Enables the generation of extended status codes. |
| GevGVCPPendingAck |
Enables the generation of PENDING_ACK. |
| GevPrimaryApplicationSwitchoverKey |
Controls the key to use to authenticate primary application switchover requests. |
| GevGVSPExtendedIDMode |
Enables the extended IDs mode. |
| GevCCP |
Controls the device access privilege of an application. |
| GevPrimaryApplicationSocket |
Returns the UDP source port of the primary application. |
| GevPrimaryApplicationIPAddress |
Returns the address of the primary application. |
| GevMCPHostPort |
Controls the port to which the device must send messages. |
| GevMCDA |
Controls the destination IP address for the message channel. |
| GevMCTT |
Provides the transmission timeout value. |
| GevMCRC |
Controls the number of retransmissions allowed when a message channel message times out. |
| GevMCSP |
This features indicates the source port for the message channel. |
| GevStreamChannelSelector |
Selects the stream channel to control. |
| GevSCPInterfaceIndex |
Index of the logical link to use. |
| GevSCPHostPort |
Controls the port of the selected channel to which a GVSP transmitter must send data stream or the port from which a GVSP receiver may receive data stream. |
| GevSCPSFireTestPacket |
Sends a test packet. When this feature is set, the device will fire one test packet. |
| GevSCPSDoNotFragment |
The state of this feature is copied into the ‘do not fragment’ bit of IP header of each stream packet. |
| GevSCPSPacketSize |
It specifies the stream packet size, in bytes, to send on the selected channel for a GVSP transmitter or specifies the maximum packet size supported by a GVSP receiver. |
| GevSCPD |
Controls the delay (in GEV timestamp counter unit) to insert between each packet for this stream channel. |
| GevSCDA |
Controls the destination IP address of the selected stream channel to which a GVSP transmitter must send data stream or the destination IP address from which a GVSP receiver may receive data stream. |
| GevSCSP |
Indicates the source port of the stream channel. |
| GevSCFTD |
Indicates the transmission delay before transmission occurs. |
| TCPEnable |
Enables TCP transfer for the selected stream channel. |
| GevSCTCPMTS |
Indicates the TCP maximum transfer size. |